Research Reconstitution Guide
Learn how to safely reconstitute research-grade peptides using bacteriostatic water, with a step-by-step laboratory reference process.
Laboratory Materials
Bacteriostatic Water
0.9% Benzyl Alcohol solution for reconstitution
Sterile Syringes
1–3ml syringes with appropriate gauge needles
Refrigeration
Fridge for proper storage (2–8°C)
Alcohol Swabs
For sterilizing vial tops before use
Peptide Vial
Your lyophilized peptide product
Sterile Workspace
Sterile environment free from contamination
Laboratory Reconstitution Reference Process
Prepare the Laboratory Workspace
Ensure you're working in a clean, sterile environment. Wash your hands thoroughly and sanitize your work surface. Remove both the peptide vial and bacteriostatic water from refrigeration and allow them to reach room temperature.
Calculate Required Volume
Determine how much bacteriostatic water you need based on the required research concentration. Use the calculator above or refer to the reconstitution table on your product page.
Sterilize Vial Tops
Use an alcohol swab to thoroughly clean the rubber stopper on both the peptide vial and the bacteriostatic water vial.
Draw Bacteriostatic Water
Using a sterile syringe, carefully draw the calculated amount of bacteriostatic water from the vial.
Add Water to Peptide Vial
Insert the needle through the rubber stopper of the peptide vial. Aim the needle at the inside wall of the vial.
Allow Dissolution
Once all the water has been added, gently swirl the vial in a circular motion. The peptide should dissolve within 1–3 minutes.
Inspect the Solution
Once fully dissolved, the solution should be clear and free of any particles or cloudiness.
Store Properly
Immediately after reconstitution, store the vial in a refrigerator at 2–8°C. Keep upright and protected from light.
Common Reconstitution Volumes
| Peptide Amount | Water Volume | Final Concentration |
|---|---|---|
| 5mg | 3ml | 1.67mg/ml |
| 10mg | 3ml | 3.33mg/ml |
| 15mg | 3ml | 5mg/ml |
| 20mg | 3ml | 6.67mg/ml |
Common Mistakes to Avoid
Shaking the Vial
Vigorous shaking can damage peptide structures. Always use gentle swirling motions instead.
Spraying Directly on Powder
Injecting water directly onto the powder can cause aggregation. Aim at the vial wall instead.
Using Plain Sterile Water
Always use bacteriostatic water containing benzyl alcohol to prevent bacterial contamination.
Improper Storage
Reconstituted peptides must be refrigerated. Room temperature storage dramatically reduces shelf life.
Not Sterilizing
Always clean the rubber stopper with alcohol swabs before each draw to prevent contamination.
Freezing After Reconstitution
Once reconstituted, never freeze peptides. Refrigerate only at 2–8°C.
Frequently Asked Questions
When properly stored in a refrigerator at 2–8°C, most reconstituted peptides remain stable for 30–45 days. Always check your specific product information, as some peptides may have different stability profiles.
No. Sterile water lacks the benzyl alcohol preservative that prevents bacterial growth. Bacteriostatic water is essential for multi-dose vials to maintain sterility throughout the usage period.
Continue gentle swirling for a few more minutes. Some peptides may take up to 5 minutes to fully dissolve. If particles persist after 10 minutes of gentle swirling, contact customer support before using the product.
Always reconstitute the entire vial contents at once. Partial reconstitution can lead to inaccurate dosing and peptide degradation. Calculate your desired concentration based on the full vial amount.
Most peptide solutions should be clear and colourless. Some peptides may have a very slight tint, but any significant discolouration, cloudiness, or visible particles indicates potential degradation. Do not use, and contact support.
Yes. Allowing both the peptide vial and bacteriostatic water to reach room temperature (15–20 minutes) helps ensure proper dissolution and reduces the risk of condensation inside the vial.
Need Further Assistance?
Our research support team is here to help with any questions about peptide reconstitution and handling.
Chat on WhatsApp